Richard
STEREO PHONO PRE-AMPLIFIER Model 4202111
Description
STEREO PHONO PRE-AMPLIFIER
Nexxtech Stereo Phono Pre-amplifier lets you use a magnetic stereo phono cartridge with an amplifier which does not have a phono input jack for a magnetic cartridge. This pre-amplifier has been designed for low noise, with RIAA compensation. This pre-amplifier requires a 9 Volt battery (not supplied) for power. For reliable operation, we recommend an alkaline type battery.
WIRING
1. Connect the left and right channel outputs of the phono player to the L (left) and R (right) INPUT jacks of the Pre-amplifier. Be sure that the phono player uses a magnetic stereo cartridge.
2. Connect the L (left) and R (right) OUTPUTS of the preamplifier to the left and right jacks of the Line input (AUX/CD/TUNER) of the stereo amplifier.
3. To turn the pre-amplifier on, slide the power switch to the “ON” position. Use your stereo phono player
and amplifier in the normal manner. Position the mode switch on the stereo amplifier to Line (AUX/CD/TUNER) to match with the input connection made.
Note: When the sound quality deteriorates, replace the battery.
SPECIFICATIONS
Input Impedance: 50k ohms at 1,000Hz Output Impedance: 50k ohms Amplitude Gain: 34dB
Maximum Permissible Input: 38mV Output Level: 1.8V RMS
Frequency Response: 30Hz to 20kHz +/-1 dB Signal to Noise Ratio: 50dB with normal input Crosstalk: Better than 50dB
Power source: 9Vdc
Dimensions: 3 5/16 x 1 1/16 x 2 5/16 inches (85 x 27 x 58 mm) Rated Input Level: 3mV
Compensation: RIAA with deviation less than +/-1dB
Current Drain: 1mA average
Nexxtech Stereo Phono Pre-amplifier lets you use a magnetic stereo phono cartridge with an amplifier which does not have a phono input jack for a magnetic cartridge. This pre-amplifier has been designed for low noise, with RIAA compensation. This pre-amplifier requires a 9 Volt battery (not supplied) for power. For reliable operation, we recommend an alkaline type battery.
WIRING
1. Connect the left and right channel outputs of the phono player to the L (left) and R (right) INPUT jacks of the Pre-amplifier. Be sure that the phono player uses a magnetic stereo cartridge.
2. Connect the L (left) and R (right) OUTPUTS of the preamplifier to the left and right jacks of the Line input (AUX/CD/TUNER) of the stereo amplifier.
3. To turn the pre-amplifier on, slide the power switch to the “ON” position. Use your stereo phono player
and amplifier in the normal manner. Position the mode switch on the stereo amplifier to Line (AUX/CD/TUNER) to match with the input connection made.
Note: When the sound quality deteriorates, replace the battery.
SPECIFICATIONS
Input Impedance: 50k ohms at 1,000Hz Output Impedance: 50k ohms Amplitude Gain: 34dB
Maximum Permissible Input: 38mV Output Level: 1.8V RMS
Frequency Response: 30Hz to 20kHz +/-1 dB Signal to Noise Ratio: 50dB with normal input Crosstalk: Better than 50dB
Power source: 9Vdc
Dimensions: 3 5/16 x 1 1/16 x 2 5/16 inches (85 x 27 x 58 mm) Rated Input Level: 3mV
Compensation: RIAA with deviation less than +/-1dB
Current Drain: 1mA average
Images:
- Ad Type: Offering
- For Sale By: Owner
Offer:
$
15
In stock
2027-01-05
https://ohmy.ca/cape-breton/buy-and-sell/audio/stereo-systems-home-theatre/stereo-phono-pre-amplifier-model-4202111_2011661.html
Richard
5/
5customer reviews
Category:
buy and sell | audio | Stereo Systems & Home Theatre
2026-11-21