MOPAR/DODGE/PLYMOUTH ENGINE PARTS.

MOPAR INVENTORY OF MORE THAN 40 YEARS.

CUDA/CHALLENGER E-BODY dash cluster/one rallye & one non-rallye.
Both not complete/to be restore or for parts. Also heater control assembly.
1971 CUDA front grille complete but in desperate need of TLC.
Has the usual cracks/damaged at passenger side corner from a fender bender.
1971 CUDA taillights in needs of new lens/license plate light assembly.
Two set of '71 front signal lights/lens in so so condition.
Stainless steel trim/black plastic interior panels/more odds & ends.
Front bumper needs straightening/handbrake assembly/under dash big round vent.
Driver side windshield wiper assembly/top cowl plastic grilles.
I have some boxes to go through still. Please inquire.

Two complete A-230 3-speed manual/A-Body short tailhousing/slip yoke design.
ONE more 3-speed all apart for parts. Bellhousings, Z-Bars & shield covers available.
They came behind slant six & your run of the mill SB in early '70s.
Package deal for all three manual transmissions.
**TWO BB 727 auto trans(PK3681054 4274 4119 & PK4028424 5654 5176).
**Both have mounting ears for floor shifter bracket. Both for rebuilt.
1972 CHARGER grille & rear sway bar complete with plates in great shape.
1976 VOLARE(F-Body) front disc brake spindles & 8.25" diff/2.94 open gears.
One BB exhaust manifold passenger side #3751074.
One SB exhaust manifold driver side #3830204.
Bendix Stromberg 2bbl carb model WW.
Clearing some DUSTER parts. Pictures available.
Slant six 225 engine & manual trans parts.

1971 CUDA 318 2bbl complete original intake/carb/air breather set up.
Timing covers, alternator brackets, distributors, crank & water pump pulleys of all types.
Many SB 318 cylinder heads & valve covers from the early '70s.
A 318 short block, many 2bbl intakes, 2bbl carbs & related engine parts.
Another 318 block punched out .055" over, hot tanked, new cam bearings installed.
TWO 318/340 crankshafts with the factory OEM balanced connecting rods.
Seven blades cooling clutch fan or RACE HEMI solid 4 blades.

1972 Dodge Charger original two piece grille.
TLC needed & some little pieces off a second one.
Perfect if you have another one in sad shape.
Also rear sway bar complete from same car.
Reasonably priced.

1976 Aspen/Volare(F-Body) front disc brake spindles.
Diff from same car 8.25"/2.94:1/pitted in one spot where was sitting/ok for cruise nights.
Housing all apart & rusty. One axle is bad at seal area.
Axle tubes showing rust inside from condensation.
Trans shop said fine after wire brushing.
Clearing price.

BARRACUDA deluxe wheel covers(14").
Were optional on all models.
Only three of them.
$25/piece OBO.

TWO small block crankshaft to choose from...
1973 340 shot-peened cast crankshaft.
Factory balanced with light duty rods(#2406782).
STD bearing size.
Rods included.
1978 318 Station Wagon cast crankshaft.
Factory balanced with HD rods(#3418645).
Rod bearing came .010" u/s from Chrysler.
Rods included.
Call for your needs.

Chrysler original radio delete plate
Part #2884773
Like new condition
Black color. No crack
Has been on the shelf since 1983
Asking $200 firm.

Chrysler air breather 1972.
The sticker showing Chrysler Corp 1972/Made In Canada.
Using air filter element #3614353.
Carb opening measuring 4.25" diameter.
Paint mark 46(assembly line?).
Offers please.

MA MOPAR factory original steel wheels
Set of four 14x5.5" B-Body or E-Body
Five of the 14x4.5" A-Body
All big bolt pattern 5x4.5"
One odd wheel size badly pitted 14x5"
To be sandblasted
Clearing prices.

TWO HD aluminum alloy rims
15x7" wide
5x4.5" B.C.
Needs polishing
Clearing $80 OBO.

TWO VINTAGE slotted mag wheels
14x6" wide
5x4.5" B.C.
Certified from Tokyo Japan sticker!?
Clearing $80 OBO.

DODGE truck flywheel 146 tooth complete assembly.
Was behind a HEMI 325 c.i. firetruck. Late 50's Dodge. For 8-bolt crank.
Ring gear diameter is 14.625''(146 tooth). Clutch disc is 11'' with 1.375'' input shaft(10 tooth).
Heavy duty pressure plate cover is 10-bolt with 4 fingers.
Chrysler generator & SUPER HD bellhousing from same truck.
Clearing $200 OBO.

TWO polished aluminum custom machined centers for Weld Racing Wheels.
Will slide fit to factory Mopar front rotors or axles center register.
Prevents damaging wheel or breaking studs if you hit a pothole.
Makes a solid installation. Goes on with the grease cap removed.
Asking $80 OBO.

Holley 4bbl carburetor / LIST-4368
Vacuum secondary / spreadbore design
Primary 1.562" / secondary 1.75"
Holley flange 4150/4160(5.16" X 5.625")
Complete / needs carb kit
Asking $100 OBO.

Dark burgundy bucket seats from a 1990/'91 Dodge Colt in good condition.
No rust on the tracks. Very light. What are you building?
Have been in my stock room for more than 20 years.
Priced to clear.

MOPAR P5249088 new adjustable proportioning valve.
TCI Automotive Roll Stop #861700.
MOOG(Federal-Mogul) shim #K8906(2.5" X 4 degree).
Please inquire.

1970 CUDA/CHALLENGER original auto trans floor console.
A one year only unique & rare factory console.
The back corner is in need of a small repair. JB WELD epoxy?
Missing top cover of storage container for some reason...
Comes with the shoulder belt buckles. One is crack?
Not concours mat'l but with some TLC, will look decent.
**I could make the necessary repairs??**

CUDA/CHALLENGER custom made auto trans floor console.
Good quality black polyurethane 4x8' sheeting(1/8" thick).
For a ratty or race car look. Nice & solid. Well made. No vibrations.
Will fit slap stick shifter. Same height as stock console.
TOO MUCH TO LIST EVERYTHING.

5/ 5customer reviews