ATLAS OH-10X EXTRA WIDE / EXTRA TALL 2 Post Lift - CLENTEC
Description
- CLENTEC - ATLAS -
- SALES - INSTALLATION - SERVICE - PARTS -
- ATLAS AUTOMOTIVE EQUIPMENT -
- TORONTO - 647 207 2081
- ST. CATHARINES - 905 246 4644
- LONDON - 226 236 7379
- $4190.00 + HST -
OH-10X EXTRA WIDE / EXTRA TALL 2 Post Overhead Lift
The Atlas OH-10X two post commercial grade above ground lift is the perfect choice for those large commercial repair facilities or The Mr. Homeowner who demands the highest quality at the absolute best price. The Atlas OH-10X is a TRUE 10,000 lb. capacity two post lift that offers a great value to the customer. The Atlas OH-10X was engineered and manufactured to lift vehicles ranging from Smart Cars ® to a one ton diesel dually. Extra lifting height and extra width between the columns allows the operator to work on all sizes of vehicles and offers a "fudge factor" of about 6 inches when "driving through" to another part of the building or lifting the van or "ladder truck". If you are over 6'2", the Atlas OH-10X has longer cylinders which allow the vehicle to be "lifted" about 3 inches higher than many other lifts.
The Atlas OH-10X has single piece columns and extra long carriages to ensure years of trouble free service. The single piece columns require the customer to have a ceiling of at least 13 feet to stand the column.
A solid column coupled with the longer carriage offers unparalleled structural support for all types of lifting requirements.
Benefits Of Our Atlas OH-10X Two-Post 10000lb Capacity Carlift
Direct Drive Cylinders
Extra long direct drive cylinders in each column allows the Atlas OH-10X to lift vehicles several inches HIGHER than many other lifts on the market. If you are over 77" tall, then this extra lifting height makes it much easier for you to walk under the vehicle.
Rubber Covers
Rubber covers on the carriages help to prevent door damage.
Padded Automatic Shut-Off Bar
The padded shut-off bar located below the cross beam prevents the top of the vehicle from being damaged by hitting the cross beam. The padded bar, when contacted, automatically shuts off the motor on the power unit to prevent the vehicle from being lifted.
Packaging
The Atlas OH-10X cannot be hauled in the back of a pickup truck. The single piece columns are almost 13 feet long. Please bring a trailer or a long bed roll back truck when you pick up the Atlas OH-10X from the warehouse or shipping terminal.
Includes Three Piece Truck Adapter Set
The included truck adapters add even more lifting height to the Atlas OH-10X. The Atlas OH-10X comes with a three piece truck adapter which offers many more lift height combinations than standard two piece truck adapter sets
Single Point Lock Release
The Atlas OH-10X has single point release which makes it easy for the operator to unlock both column locks from one column.
Overhead Bar Configuration
The overhead bar configuration of the Atlas OH-10X leaves the area between the columns open, and allows the operator to easily roll a transmission jack or a tool box under the car.
Symmetric Columns
The symmetric column design provides a very wide drive through area to accommodate dual wheel pickups. The Atlas OH-10X cannot be hauled in the back of a pickup truck. The single piece columns are almost 13 feet long. Please bring a trailer or a long bed roll back truck when you pick up the Atlas OH-10X from the warehouse or shipping terminal.
Single Piece Columns And Extra Long Carriages
The Atlas OH-10X incorporates a single piece 12' 7" formed column and an extra long carriage that provides maximum column and arm strength to lift and support a 10,000 lb. vehicle.
Electrical Requirement
The electric motor for the power unit requires 220 Volt (single phase) 60 Hz. We recommend using at least a 10 gauge (grounded) wire from the electrical panel. The power unit has a short pigtail (no plug) that can be wired to either a quick disconnect box (mounted on the lift column) or to a male/female plug combination. A 30 amp breaker is recommended.
Installation
Most of our above ground lift customers install their own car lifts. The average time to install the Atlas OH-10X car lift is four hours. We provide detailed installation instructions with all our two post above ground lifts and our four post above ground lifts.
HIGHLIGHTS;
•10,000 lb. capacity
•Inside Column Width: 117 1/2" (9' 9 1/2")
•Direct Drive Cylinders
•Symmetric Columns
•Heavy Duty 2 Stage Symmetric Arms
•Automatic Arm Restraints
•Overhead Design
•Single Point Lock Release
•Atlas® Powder Coat Finish
•Mounting Hardware Included 5 Year Structural Warranty, 2 Year Hydraulic Cylinder Warranty, and 1 Year Power Unit Warranty
•Free 12 Piece Truck Adapter Set
•Shipping Weight: 1,665 lbs.
SPECIFICATIONS;
Capacity - 10,000 LB.
Overall Height - 151 1/2" (12' 7 1/2")
Padded Bar Height - 144" (12')
Overall Width - 143 3/8" (11' 11 3/8")
Outside Column to Outside Column - 135 7/8" (11' 3 7/8")
Maximum Lift Height - (With Adapters) 84" (7')
Minimum Arm Height - 4"
Inside Column - 117 1/2" (9' 9 1/2")
Column Size - 11" x 9 1/8"
Column Thickness of Steel - 5mm
Carriage Thickness of Steel - 5mm
Arms Thickness of Steel - 6mm
Drive Thru - 106 1/8" (8' 10 1/8")
Base Of Lift - 18 1/2" x 21 1/2"
Cable Diamter - .375"
Motor/Electrical Requirement - 3HP, 220V +/- 5% (209-231volts) single (1) phase.
A 30 amp breaker is required.
Oil Requirement - 3-5 Gallons AW32/AW46
Requires a minimum of 4" of concrete with 3000 psi.
- $4190.00 + HST -
DELIVERY / INSTALLATION AVAILABLE
- CLENTEC - ATLAS -
- SALES - SERVICE - PARTS -
- TORONTO - 647 207 2081
- ST. CATHARINES - 905 246 4644
- LONDON - 226 236 7379
- Ad Type: Offering
cars & vehicles | other
2021-03-17